Search
Close this search box.

3D printed circuit boards in the area of conflict between functionality and cost optimization

KSG rigid-flex printed circuit board

How to reduce costs in the production of rigid-flex printed circuit boards

Whether energy, raw materials or personnel - there is hardly any area at present that is not affected by exorbitant cost increases. This also affects the production of printed circuit boards. This makes it all the more important to look for potential savings, especially for complex components such as rigid-flex printed circuit boards. Several levers can be identified here that can contribute to greater cost efficiency.

Selecting the right base material

The base material is an important factor that can be influenced. It accounts for around 25-35 % of the manufacturing costs and is a significant influencing factor with regard to the process reliability and reliability of the PCB. The base material should therefore always be selected according to the operating conditions and thermomechanical load. The question "What is really necessary?" plays a central role here. 

KSG cost comparison for rigid-flex printed circuit boards

Cost comparison of different body variants

Concept of the layer structure

With rigid-flex PCBs, the right choice of layer structure is also cost-relevant. Considerable cost differences must be taken into account between layer structures such as "Asymmetrical one flex layer", "Asymmetrical two flex layers" or "Symmetrical two flex layers". These can be up to 200 % additional costs at peak times. In the Digital Design Compass you will find, among other things, the appropriate technical design-to-cost recommendations. 

The right number of layers

A cost-oriented architecture is also based on the number of layers. This not only saves material, but also an entire production run of inner layer production per laminate, which corresponds to six to twelve work steps. If it is possible to reduce the multilayer structure by just one laminate, cost optimizations in the double-digit percentage range are often possible, depending on the complexity.

Avoidance of multiple grouting

In addition, the pressing process is a significant cost driver. Multiple pressings mean multiple passes through an entire process chain and should therefore be avoided if at all possible. In this respect, it is advisable to avoid buried vias and to realize all connections from the outer layers if possible. In this way, one pressing and one drilling operation can be saved.

Optimum material utilization

One aspect that has a direct impact on all process costs is material utilization. If you want to operate efficiently here, you must therefore ensure optimum material utilization. This means that tolerances should only be as tight as absolutely necessary and you should concentrate on individual specifications or minimal restrictions for the design of benefits. Close coordination with the manufacturer is recommended here with regard to the cutting and PCB/panel sizes to be used, as offered by the KSG Group as part of its technical support.

Standardization instead of individualization

Even though there are no limits to individuality in the design of printed circuit boards nowadays, this is considered a cost driver. In order to be able to act as cost-efficiently as possible - especially with regard to quantity-dependent material purchase prices - standardization is required. Where technically possible, a dual-ply structure, standard laminate thicknesses and base copper thicknesses of 18 µm or 35 µm should be used. The use of bonded instead of non-bonded materials also makes a significant cost difference.

Just like individualization, miniaturization also costs money and, above all, drives up material prices, which is why the line space requirements should be as large as possible. This means that the manufacturer can work with standard copper thicknesses and does not have to resort to carrier-based copper foils in thicknesses of 9 µm or 5 µm, which have a material price that is up to 12 times higher.

Further XPERTS recommendations for rigid-flex PCBs:

  • Involve the supplier in the development process as early as possible. 
  • Only restrict tolerance windows where absolutely necessary.
  • Leave the delivery panel design to the supplier so that the circuit can be optimally aligned to the respective production panels.
  • Specify the product so that the manufacturer can use flex lacquer instead of coverlay film for exposed, flexible areas. The application process is more cost-efficient due to the high degree of automation.
  • If possible, switch to semi-flexible PCBs so that cost-intensive polyimide material can be dispensed with. In addition, the effort required for mechanical processing is reduced and lower drilling, milling, cleaning and metallization costs are incurred.

Do you have any questions on this topic? Then please leave a comment! We look forward to your feedback.

One Response

  1. Dear Ms. Kaulfuß,
    Thank you very much for the interesting price scale depending on the Flex-Starr structure. This helps to get an overview of possible savings potential compared to the technical realization.
    Best regards
    Steffen Braun

Leave a Reply

Your email address will not be published. Required fields are marked *

en_USEnglish